I know the long waiting list of Blitzortung but I paid more than two months ago after order confirmation and I have not yet received the system blue 19.4.

Is this delay normal? 

Regards,
Manuel

Very dead day lightning wise in region 3. Looking at three of the sites in NC, virtually no signals. 

   

Hello. My system Blue is working, but I would like to optimize it and eliminate or try to cut down some of the noise. I am using 2 200mm ferrites which are placed indoors in the same room as the controller. Here are three screen grabs of my signals during a quiet time..no lightning and no "faults" where all 3 LED's are lit. The last trace (channel 2A)seems to me to be the most problematic; it appears as a sawtooth well above 0 volts. Could this be a power supply issue or external rf interference from some yet indeterminate source?

Thanks,  Steve

Attached Files

Thumbnail(s)
           

A Danish guy is doing an excellent job, testing among other USB chargers.

/Richo


https://lygte-info.dk/info/ChargerIndex%20UK.html

Hi All
A bit of a continuation of my Lost Controller thread. 
As someone suggested the Vonets wifi connection I thought I would try it. It's a much neater unit than the old access point I got working.  I managed the get the router to see the controller's IP but I can't get a connection through the browser. Also the network led pulses. Looking closely the Vonet rj45 plug seems only to have pins 2 and 3 connected.  So what are the pins used by the controller RJ45 network socket ?
Regards
Alan

Hi All
Blue system windows 7
I have been trying to set up a shared network having changed from a wired to wireless network for the pc's. Obviously the controller has to stay on wired. Win 7 sets the lan adapter to an ip of 198.162.100.1 for a shared network so before doing this while I could still access the controller I set the dchp to enable and changed the ip to 198.162.100.10 
Now if I ip scan the 100's I can no longer find the controller. Is there a way of doing a reset and what would the default ip then be. I have tried a power off and on but still no luck.
I am still getting a flashing network led although when I have made contact the data seems to be flowing OK (noise floor shows a continuous trace)
I'm rather stuck so HELP !!! Please !
Regards
Alan

Hi All
Blue system 
Suddenly the network led has started flashing on/off at about 1 second intervals. The led keeps on flashing even with the network unplugged. An IP scanner shows up the IP and noise floor switched on shows a continuous trace.
Any ideas ?
Alan

Hi
I quite often compare my performance with others fairly close to me on Signal vs Strikes.
I was looking at the statistics for Bridport Dorset UK which is a station not too far from me and noticed how many thousands of signals were produced.
Looking at the signal graph it shows regular E signals and I wondered if a nearby radar installation, maybe at Royal Navy Air Station at Yeovilton, was the cause.
Has anybody else noticed anything similar.
Regards
Alan

Hi All
I have my antenna on a window sill where it seems to get best reception. I recently put a new mobile wifi hub within a couple of hundred centimetres and it, I think, created huge interference. Moving it away to about 1/2 metre and the interference looks as though it has stopped. I have no idea why it should happen but it might be a clue for others.
Regards
Alan

Hello,

I'm on the last legs of setting up my Blue system and have some questions.

1) On the pre-amp board are the connectors A-1,A-2 and B-1,B-2 relate to the vertical antennas?
2) On the pre-amp board is the connector C-1,C-2 for the optional horizontal antenna?
3) I intend to use my loop antenna I had on my Green system, Which I was under the impression it did not matter which way it pointed, is this still so?
4) On the Green system the loop antenna windings were wound in a certain direction, and had to be wired up to the Green pre-amp the correct way, is this still so for the Blue system, if so which end of the loop goes to which connector (1, 2) ?

Regards John