| Welcome, Guest |
You have to register before you can post on our site.
|
| Latest Threads |
Data Request - 7/4/25
Forum: General Discussion
Last Post: Eric.Wouters
1 hour ago
» Replies: 1
» Views: 40
|
Sold - System Blue Classi...
Forum: General Discussion
Last Post: byronbay
2026-04-27, 06:21
» Replies: 9
» Views: 5,500
|
Request for non-commercia...
Forum: Website, Maps and Applications
Last Post: GalenIvor
2026-04-23, 10:49
» Replies: 2
» Views: 1,829
|
Request for historical da...
Forum: Website, Maps and Applications
Last Post: aker
2026-04-22, 07:11
» Replies: 0
» Views: 382
|
Where to see error improv...
Forum: Hardware, Software, Lightning Physics
Last Post: MDuperrier
2026-03-25, 15:22
» Replies: 9
» Views: 4,329
|
System Blue H-field only
Forum: General Discussion
Last Post: gmiller43
2026-03-21, 16:29
» Replies: 2
» Views: 2,998
|
Help linking account
Forum: General Discussion
Last Post: jamieh
2026-03-21, 03:43
» Replies: 6
» Views: 7,145
|
How to see private messag...
Forum: General Discussion
Last Post: Buckethead
2026-03-15, 21:22
» Replies: 0
» Views: 1,447
|
Station 18, with green pc...
Forum: Hardware, Software, Lightning Physics
Last Post: PetrosKa
2026-03-13, 13:44
» Replies: 1
» Views: 2,657
|
Power Supply
Forum: Hardware, Software, Lightning Physics
Last Post: Eric.Wouters
2026-03-08, 11:14
» Replies: 2
» Views: 2,654
|
|
|
| Firmware 10 on System Red PCB 10.5 - firmware bug ??? |
|
Posted by: mmlightning - 2024-06-24, 16:47 - Forum: Hardware, Software, Lightning Physics
- Replies (1)
|
 |
Hello,
I installed the new firmware on my PCB 10.5 controller for System red. The PCB was manufactured according to schematic and Eagle-File:https://docs.lightningmaps.org/files/hardware/red/PCB_10_5.brd
The firmware did not work properly as the PCB-ID was not detectected correctly. It turned out that PCB 10.5 has a different coding then described.
Description according to the hardware reference in TablePCB Controller Ids:
https://docs.lightningmaps.org/hardware/...system-red
Id PCB System PD10 PD11 PD3 PD1 Offset
2 10.5 RED - + - - 0
but it turned out that actually Coding of PCB 10.4 and PCB 10.5 is different, PCB10.5 has the following coding:
Id PCB System PD10 PD11 PD3 PD1 Offset
? 10.5 RED + + - - 0
this can also be seen in the schematic of PCB 10.5, so PD10 has a high level +5V instead of GND like PCB 10.4.
I did cut off pin PD10 from the controller-board and now all is working; PCB 10.5 is detected as PCB10.4 now
... but it seems that there is a firmware bug in 10 RED ???? This potentially could affect several stations, as station list has decreased since new firmware is out
|
|
|
| Are there any hams on this sub who are involved with the lightning project |
|
Posted by: hermanjackson - 2024-06-19, 07:05 - Forum: Website, Maps and Applications
- Replies (4)
|
 |
I continually monitor BLITZORTUNG.ORG because lightning in Utah can pop up very strong and very quickly in the summer. My question is: are there any hams that are involved with this system to receive and report lightning strikes, anywhere in the world. Is the board difficult to populate, and does it require any surface mount components? What about the receiving antenna...I see a lot of variations and wonder which type has shown the best success. My QTH is only two miles west of the Wasatch Front...part of the Rocky Mountains. I'm at 4400 feet and the mountains go to about 7500 feet, so there is the possibility that I might not be able to "see" lightning to the east of me. Thanks for any advice or ideas.
|
|
|
| Lightning location? |
|
Posted by: henry - 2024-06-11, 11:12 - Forum: General Discussion
- Replies (2)
|
 |
Hi everyone,
I am doing an analysis of lightning and was wondering whether there is some "relatively" exact location of the lightning available (such as the latitude and longitude) or if I need to estimate this from the map. (I know the location is not exact but does Blitzortung provide at least an estimate?)
Thank you very much!
|
|
|
|