LED placement question

[SteveQlQ]

Hi: almost finished with the build and no problems so far.

I have a question about the LED order. I know it really doesn't matter, but to be consistent with everyone else, which of the following is correct. I must add that I am somewhat red/green color blind: I can see a lit LED fine, but on a printed page...not so good.

On the front panel picture it appears as if this is the order is (starting L to R with Power)  R, G, G. Y, B, R, R



below that picture it shows the controller board with the order of R (on right of picture, would = Power on front panel), G, G, R, B, then whatever on the right of the front panel (Y,R or R,Y) . I know this is a silly question, but for consistencies sake, I thought it is worth it.

Steve

[JupiterJoe]

Hi: almost finished with the build and no problems so far.

I have a question about the LED order. I know it really doesn't matter, but to be consistent with everyone else, which of the following is correct. I must add that I am somewhat red/green color blind: I can see a lit LED fine, but on a printed page...not so good.

On the front panel picture it appears as if this is the order is (starting L to R with Power)  R, G, G. Y, B, R, R



below that picture it shows the controller board with the order of R (on right of picture, would = Power on front panel), G, G, R, B, then whatever on the right of the front panel (Y,R or R,Y) . I know this is a silly question, but for consistencies sake, I thought it is worth it.

Steve

On my housing, I have R, G, G, Y, B, R, R. The only yellow LED is the Fault indicator.

[SteveQlQ]

Hi: almost finished with the build and no problems so far.

I have a question about the LED order. I know it really doesn't matter, but to be consistent with everyone else, which of the following is correct. I must add that I am somewhat red/green color blind: I can see a lit LED fine, but on a printed page...not so good.

On the front panel picture it appears as if this is the order is (starting L to R with Power)  R, G, G. Y, B, R, R



below that picture it shows the controller board with the order of R (on right of picture, would = Power on front panel), G, G, R, B, then whatever on the right of the front panel (Y,R or R,Y) . I know this is a silly question, but for consistencies sake, I thought it is worth it.

Steve

On my housing, I have R, G, G, Y, B, R, R. The only yellow LED is the Fault indicator.

[SteveQlQ]

Thanks, Joe..I thought the front panel picture would be the correct one, so since you confirmed my colors, I will finish using that.

Steve

[JupiterJoe]

Thanks, Joe..I thought the front panel picture would be the correct one, so since you confirmed my colors, I will finish using that.

Steve

Awesome man! Let us know when you're online!

[Nekota]

Hi: almost finished with the build and no problems so far.

I have a question about the LED order. I know it really doesn't matter, but to be consistent with everyone else, which of the following is correct. I must add that I am somewhat red/green color blind: I can see a lit LED fine, but on a printed page...not so good.

On the front panel picture it appears as if this is the order is (starting L to R with Power)  R, G, G. Y, B, R, R



below that picture it shows the controller board with the order of R (on right of picture, would = Power on front panel), G, G, R, B, then whatever on the right of the front panel (Y,R or R,Y) . I know this is a silly question, but for consistencies sake, I thought it is worth it.

Steve

For what it's worth there are LED chips on the main board and I thought they should match the case LEDs. The board chip LEDs are R G G R B R Y which makes more sense as the signal LED shouldn't be a fault indicator.

[cernese]

I wish I had read this before finishing my kit :-|