Blitzortung.org Forum › Public Forums › Hardware, Software, Lightning Physics v
Unassembled kit pics

Threaded Mode
Unassembled kit pics
Donald.Froula Offline
Participant
Posts: 346
Threads: 36
Joined: 2013-07-10
#1
2014-03-04, 17:38
I'm building up a station for a new member.

For those considering ordering and building a kit, here's what it looks like just out of the box!

Don


Attached Files Thumbnail(s)
                       

Stations:
Reply
Egon Offline
Developer
Posts: 899
Threads: 55
Joined: 2012-06-26
#2
2014-03-16, 20:06
Note that this is only the basic amplifier and controller kit, without STM32F4DISCOVERY board, ferrite rod antennas, external GPS antenna, power supply, and connection cables. This is what we usually send to countries outside of Europe.

Egon
Stations: 3071, 3073, 3074
Website
Reply
jjregist Offline
Registered forum member
Posts: 1
Threads: 0
Joined: 2014-04-07
#3
2014-04-07, 20:42
Hello,

I am a young electrical engineer and scientist in Tampa FL(USA) and I am eager to get started with a contribution to the project with a station here at my house. Please Tell me how much to send and where to for the basic kit. I have the auto generated email sent to me but I am unsure of shipping. I have prototyping experience and can help with the programming effort for the group. I have already begun construction of the antennas as per the PDF. Please PM me.

Joe Register
Reply
Donald.Froula Offline
Participant
Posts: 346
Threads: 36
Joined: 2013-07-10
#4
2014-04-09, 00:48
You've got mail.

(2014-04-07, 20:42)jjregist Wrote: Hello,

I am a young electrical engineer and scientist in Tampa FL(USA) and I am eager to get started with a contribution to the project with a station here at my house. Please Tell me how much to send and where to for the basic kit. I have the auto generated email sent to me but I am unsure of shipping. I have prototyping experience and can help with the programming effort for the group. I have already begun construction of the antennas as per the PDF. Please PM me.

Joe Register
Stations:
Reply
Vad Offline
Participant
Posts: 24
Threads: 7
Joined: 2014-04-15
#5
2014-04-18, 15:50
(2014-04-09, 00:48)Donald.Froula Wrote: You've got mail.

Me too, please.
I think AMP kit + PCB controller...
what will be the total cost?
Shipping to Russia
Website
Reply
Remy Brandt Offline
Participant
Posts: 15
Threads: 1
Joined: 2014-05-21
#6
2014-05-21, 16:51 (This post was last modified: 2014-05-21, 17:02 by Remy Brandt.)
I have two questions,what antenna is preferred? I live in a radio sweet spot Mussel,Bourtange and Sellingen are my potential locations (all three of them if I like it) with very little electrical noise so the wire antenna should do well here.
And about soldering,I can solder like the best but have no SMD soldering station,On the pictures it looks like those processor boards come completely assembled,are there any more really dense microchips that have to be SMD soldered?

I want to buy a complete kit and make my own antenna and not while being in the process notice that I don't have some crucial bits that take another few weeks to order Smile
Reply
RichoAnd Offline
Developer
Posts: 1,220
Threads: 77
Joined: 2012-07-01
#7
2014-05-21, 19:45
E-Field antenna should be fine
There are only some op amps, and a GPS requiring a small soldering iron.
Processor board come completely assembled.

/richo
Stations: 584, 585, 2017
Website
Reply
preape Offline
Registered forum member
Posts: 1
Threads: 0
Joined: 2014-06-17
#8
2014-06-17, 13:29
I live east of Lake Ontario, and in the winter we get intense Lake effect snow, which produces lightning in some of the most intense bands. I am also a amateur radio operator with electronic skills. I am very interested in putting together on of these kits.
Paul.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)